I Stoc Táirge Te
HC-K 6/12-EBUS
HC-K 6/12-EBUS 1636363 PHOENIX CONTACT Contact insert
$127.97
USD
i stoc
Sonraíochtaí Príomhúla
:
Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Cineál:
B16
Leithead:
34 mm
Airde:
47 mm
Faisnéis faoi Sholáthraithe
Táirgí: 0
Seoltar laistigh de 2-3 lá gnó de ghnáth
Cáilíocht Ráthaithe
Loingseoireacht Thapa
Tacaíocht Theicniúil
Sonraíochtaí Teicniúla
| Paraiméadar | Luach |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Cineál | B16 |
| Leithead | 34 mm |
| Airde | 47 mm |
| Fad | 84.1 mm |
| Sraith | HC-K |
| Ginearálta | For HEAVYCON ADVANCE and HEAVYCON housing of type B16/B32, axial connection for 2 mm Allen wrench |
| Feidhmchlár | Power/signal |
| Cineál táirge | Contact insert with a fixed no. of positions |
| Nóta tionóil | To ensure correct use, installation in housing with IP54 protection or better is required |
| Sruth rátáilte | 40 A (power contacts) |
| Athbhreithniú airteagail | 04 |
| Trastomhas teagmhála | 4 mm |
| Ábhar teagmhála | Cu alloy |
| Uimhriú teagmhála | 1 - 6 (power contacts) |
| Lann scriúire | 0.5 x 3.5 mm (control contacts) |
| Chasmhóiminte teannaithe | 2 Nm ... 2.5 Nm (PE connection) |
| Próifíl nasc | 6+12+PE |
| Céim an truaillithe | 3 |
| Líníocht thoisí | |
| Líon na bpost | 18 |
| Voltas borrtha rátáilte | 8 kV (power contacts) |
| Catagóir róvoltais | III |
| Teicneolaíocht nasctha | Axial screw connection (power contacts) |
| Cineál ábhar teagmhála | turned |
| Líon na dteagmhálacha cumhachta | 6 |
| Voltas rátáilte (III/3) | 690 V |
| Trasghearradh seoltóra | 2.5 mm² ... 10 mm² (power contacts) |
| Líon na dteagmhálacha rialaithe | 12 |
| Ábhar iompróra teagmhála | PC |
| Timthriallta iontrála/aistarraingthe | ≥ 500 |
| Trasghearradh nasc AWG | 12 ... 8 (power contacts) |
| Teocht chomhthimpeallach (oibriú) | -40 °C ... 125 °C |
| Fad an phoill druileála, cothrománach | 77.5 mm |
| Voltas rátáilte le haghaidh teagmhálacha cumhachta | 230/400 V |
| Rátáil inadhainteachta de réir UL 94 | V0 |
| Fad stialladh na sreinge aonair | 8 mm +1 mm (Power 6 mm² ... 10 mm²) |
| Ábhar dromchla teagmhála, teagmháil chumhachta | Ag |
| Ábhar dromchla teagmhála, teagmháil rialaithe | Ag |
Cur Síos ar an Táirge
Contact insert, number of poles: 6+12+PE, size: B16, power contacts: 6, control contacts: 12, Female, Axial screw connection, 690 V, 40 A, 2.5 mm² ... 10 mm², application: Power/signal
Príomhghnéithe
- Cáilíocht ghrád tionsclaíoch
- Comhlíontach le RoHS
- Deimhnithe CE
- Barántas 1 bhliain
Doiciméid Táirge
Bileog Sonraí
Sonraíochtaí teicniúla agus sonraí feidhmíochta
Lámhleabhar Úsáideora
Treoir suiteála agus oibríochta
